Features:
1. With power-off memory
2. The function of anti-reverse connection of power supply will not damage the module due to wrong connection of power supply.
3. Timing accuracy to 0.01 second timing. 0.1 second (minimum) ~ 999 minutes (maximum) optional
4. Low power consumption and power saving settings, you can turn off the display area.
5. Wide range of applications: it can be applied to water pump control, motor control, light belt control, solenoid valve control, etc.

Parameters:
Commodity name: Multifunctional time delay relay
Relay V number: DC5V/12V/24V optional
Input voltage: 5V version: DC5V power supply; 12V version: DC12V power supply; 24V version: DC24V power supply
Output load: DC 30V, maximum 10A. AC 250V, maximum 5A.
Trigger signal: 5V version (high level: 5V); 12V version (high level: 12V), 24V version (high level: 24V) and low level are OV.
Quiescent current: 20mA
Working current: 60mA
Working temperature: -25°C-85°C
Power off memory: Yes
Wiring port description:
Input DC power positive pole: DC+
Input DC power negative pole: DC-
Positive pole of signal input terminal: IN+
Negative pole of IN- signal input terminal: IN-
The normally open interface of the relay is short-circuited with COM when the relay is closed and suspended when it is not closed: NO
COM Relay public port interface: COM
When the normally closed end of the relay is not connected, the relay is shorted with COM and suspended when the connection is closed: NC

Working mode (32 types)
P-11: Jog mode, pull in with signal, disconnect without signal.
P-12: Self-locking mode, the relay state flips once every time it is triggered.
P-13: After triggering, the relay is closed and disconnected after a delay of time A; the trigger is invalid during the delay.
P-14: After triggering, the relay is closed and disconnected after a delay of time A; the trigger restarts timing during the delay.
P-15: After triggering, the relay pulls in & turns off after a delay of A time; triggers the cumulative timing during the delay.
P-16: After triggering, the relay pulls in & disconnects after a delay of A time; trigger reset during the delay (the relay is disconnected)
P-17: After triggering, the relay is closed during the duration of the signal, the input signal disappears, and it is disconnected after a delay of A; when the relay is triggered again during the delay, the timing stops until the last signal disappears, and the delay is A Disconnect after time.
P-18: After the power is turned on, the relay will be closed immediately, and will be turned off after a delay of A seconds; until the next time the power is turned on.
P-21: Give the signal, the relay picks up after a delay of A time.
P-22: Give a continuous signal, after the time A exceeds, the relay will pull in; when the signal disappears, the relay will be disconnected.
P-23: If the signal disappears for more than A time, the relay will be closed; if there is a signal, the relay will be disconnected.
P-24: Give continuous signal, after A time, the relay will pull in; if the signal disappears for A time, the relay will be disconnected.
P-25: Give the continuous signal, after the time A exceeds, the relay will pull in; give the continuous signal again, after the time A exceeds, the relay will disconnect
P-26: When the signal is given, the relay will be closed after A time; after the signal disappears, the relay will be closed again for A seconds and then stop
P-27: When there is a pulse signal (rising edge or falling edge), the relay is disconnected, and if there is no pulse signal, the relay picks up after a time delay of A (continuous high level or continuous low level is regarded as no pulse).
P-28: After power on, the relay will pick up after a delay of time A until power off.
P-31:. After power on, the relay pulls in for A time and disconnects for B time, infinite cycle; power off to stop.
P-32: There is a continuous signal, the relay pulls in for A time, disconnects for B time, infinite loop; the signal disappears, and the cycle is terminated.
P-33: Give a signal once, the relay will be closed for time A, and disconnected for time B, and the cycle will be infinite; give another signal to terminate the cycle.
P-34: After power-on, after a delay of time A, the relay pulls in & turns off after pulling in time B.
P-35: Give a signal once, and after a delay of time A, the relay will pull in & turn off after pulling in time B.
P-36: Give a continuous signal, after the time A exceeds, the relay will be closed, and after the time B is closed, it will be disconnected; the signal disappears, the timer is reset, and the relay is disconnected.
P-37: When there is a signal, the relay will automatically disconnect after the A time, and then count the B time after disconnection. The signal trigger is invalid during the A+B time.
P-38: When there is a signal, the relay will automatically disconnect after the A time, and then count the B time after disconnection, and then automatically disconnect after the A time again.
P-41: No action when there is a signal; trigger when the signal disappears; the relay pulls in & disconnects after a delay of time A.
P-42: The signal disappears, and the relay is closed after a delay of time A; the relay is disconnected after a delay of time B.
P-43: The signal disappears. After the disappearance exceeds the time A, the relay is closed; after a delay time B, the relay is disconnected.
P-44: After power on, the relay will be closed for A time and disconnected for B time; after C cycles, the relay will be disconnected and stop.
P-45: No action after power-on; after the signal is given, the relay will be closed for time A and disconnected for time B; after cycle C times, the relay will be disconnected to stop; if the signal is given, it will be executed again.
P-46: After the signal is given more than A times, the relay pulls in; keeps pulling in; power off to stop.
P-47: After the signal is given for more than A times, the relay will be closed; after the time B is closed, it will be disconnected.
P-48: During the time C, after the signal is given continuously for more than A times, the relay will be closed and then stop after the B time.

Package Include:
1x Relay
1x Button cap
2x Screw piece