माल मिले के 40 दिन के भीतर रिटर्न स्वीकार कइल जाई। कस्टम आइटम रिटर्न ना कइल जा सके। गिफ्ट कार्ड से खरीदल गइल आइटम बदलल जा सके।
मुफ्त उपहार
Roymall में आपका स्वागत है, प्रीमियम उपहार की आपकी दुकान। हम आपके समर्थन की सराहना करते हैं और आभार के रूप में हर खरीद पर मुफ्त उपहार प्रदान करते हैं।हमारे संग्रह को देखने के लिए तैयार हैं? हमारे चयन को ब्राउज़ करें, अपना ऑर्डर दें और अपने खरीद के साथ मुफ्त उपहार प्राप्त करें।
शिपिंग नीति
हम ऑर्डर 2 दिन में संसाधित करते हैं।सामान्य शिपिंग समय 5-7 कार्य दिवस है।गंतव्य के आधार पर शिपिंग समय अलग हो सकता है।
1. रिटर्न नीति
हम केवल roymall.com से खरीदल गइल आइटम स्वीकार करत बानी।मुफ्त उपहार रिटर्न ना कइल जा सके।रिटर्न कइल जाए वाला आइटम अप्रयुक्त और मूल पैकेजिंग में होन चाहीं।हम रिटर्न 3-5 कार्य दिवस में संसाधित करत बानी।कस्टम आइटम रिटर्न ना कइल जा सके।संपर्क करीं: service@roymall.com या Whatsapp: +447549870296
2.धन वापसी नीति
रिटर्न आइटम मिले के बाद पूरा धन वापस मिली।शिपिंग लागत वापस ना मिली।संपर्क करीं: service@roymall.com या Whatsapp: +447549870296
Videos for similar product
Loading product videos...
❮
❯
Products related to this item
Loading related products...
❮
❯
Feature:
Model: STM32F103C8T6
Kernel: ARM32 bit Cortexu2122-M3CPU
Size: 22.86mm x 53.34mm
Debug Mode: SWD
MCU Introduction:
1. The maximum operating frequency of 72MHz
2. Single-cycle multiply and hardware divide
3. 64k Flash program memory
4. 20k bytes SRAM
5. 2.0-3.6V power supply and I / O pins
6. On power-up, power reset (POR / PDR), programmable voltage monitor
7. 4-16MHz crystal oscillator
8. Embedded 8MHz RC oscillator
9. generates CPU clock PLL
10. Sleep Stop Standby mode
11. VBAT power for the RTC back registers
12. 37 Quick I / O ports, the I / O ports can be mapped to 16 external interrupts etc.
The PCB with STM32F103C8T6 on board works fine, can be programmed from stm programmers. It is one very serious trouble - ADC noise is very very larga, more than 5-6 units becouse of pcb desing. Be carefull with using the pcb as ADC. You can see the ADC noise on Figure.
The edges of the PCB are not burnished, but it is not a big deal - can be done easy with sandpaper.
There is one design issue with this 48 pin package - the CAN module and the USB share the same pins, that means that you can't use both in same project.